12x8 CabanaGarden ShedAssembly ManualSome of the safety and usage measures you may wish to consider include:-snow load ratings vary by geographical lo
19. Start positioning and securing wall panels around your floor. Attach wall studs together as perStep 17.20. Complete all side and rear wall attachm
22. Place 2nd Window Wall Panel infront and attach. Insert 2nd WindowInsert as per Step 21.23. Position and attach Narrow Wall Panel to left side wal
27. Position Side Top Plates(one side only) on top of wallstuds so they are flush on theinside with 2x3 wall stud. Thereare 3 pieces of Side Top Pla
29. Position Side Top Plates on other side wall top framing to complete. Use 4 - 2” screws per piece.28. Next, attach the 4 Front and Rear Top Plates
31. Lift up a completed gable section and place on top of Side Top Plate on wall. The gable framing should sit flush with the inside of the top plate
C. & D. Rafter and Roof SectionToll Free 1-888-658-1658 www.outdoorlivingtoday.com [email protected] 15Outside
Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [email protected] 1637. Attach end of a 68 1/4” long Soffit Bo
38. Starting with the rearSide, lift completed raftersection up. Note: Soffitmust be facing down. 40. When Rafter Section is correctly positioned, out
41. Place 2nd completed Rafter Section on gable wall framing. Position as per Steps 39 & 40.Gable NotchRidge BoardRafterOffsetting MetalRidge Boa
45. Roof Gussets are positioned on middle rafters. When correctly positioned, slide gusset up,using a level to square, and attach to rafters with
Thank you for purchasing our 12x8 Cabana Garden Shed. Please take the time to identify all the parts prior to assembly.Parts List:A. Floor Section 3
48. Locate Middle Roof Panel and place on middle rafters. With Middle Roof Panel aligned as perStep 46, tack panel down to rafters with 2 - 2.5” scr
OutsidePanelMiddle Panel OutsidePanel51. With Front Roof Panels positionedcorrectly, tack down as per Steps 46-49.50. Position and attach Front Roof P
E. Miscellaneous SectionCedar Roof Ridge CapsFront andRear Facia(4)HorizontalGableTrim (4)Bottom Skirting Sides (4)NarrowTrims (9)FlowerBoxes (2)Penta
58. Attach Wide Corner Trim and Narrow Corner Trim in each corner. Wide Trims are 4 1/2” wide.Narrow Trims are 2 1/2” wide. Butt Wide Trim against the
60. Attach Rear Wall NarrowTrim (2 - 1/2” x 2 1/2” x 79”) wherewall panels come together andleave a seam. Position trim equally on wall seam and flus
65. Position Doorway Narrow Trims (2 - 1/2” x 2 1/2” x 79) flush with inside of door jamb and flushwith Bottom Skirting. Attach with 8 - 1 1/4” fini
66. Attach Facia/Trim Detail Plates to cover seam where facia and horizontal trim pieces cometogether. Secure each with 4 - 1 1/4” finishing nails. T
72. To complete trimming of your Door, attachboth the Horizontal Door Trim and HorizontalNarrow Wall Trim with 4 and 2 - 1 1/4” finishingnails.71. Pl
74. Attach Interior Door Stops to doorframing. Start with Horizontal piece first. Use4 - 2” screws to secure each Stop. Stopsshould overlap door by ap
We hope your experience constructing our building has been both positive and rewarding.We value your feedback and would like to hear back from you on
12 x 8 CABANA HARDWARE SHEET2 1/2”Note: screws and nails shown actual size.2”1 1/4”3/4”2” 3/4”1 1/4” 1 1/4”Tee Hinge x4Pull HandleBlack SilverBlack F
A. Floor Section1. Lay out Large Floor Joist Frame and 2 Floor Joists as illustrated above. Position Joists equally in Floor Joist Frame. Use Small F
7.Attach Floor Runners to completed floor frame.There are 2 floor runners per 136 1/2” side and 5completed runners in total. Use 6 - 2.5” screws perRu
Note: The floor will be flipped over and the floor runners will sit on your foundation. It is important to note, thathaving a level foundation is crit
13. Lay out all the wall panelsand become familiar with theirlocation. On Standard Kits, there are 2Window Wall Panels, 7 SolidWall Panels
15. Starting at Rear Corner, position a Solid Wall Panelon top of plywood floor. The Wall Panel bottom framing willsit flush with plywood. Wall siding
Do Not Attach Walls ToFloor Until Step 2617. Position side solid wall into place onplywood floor. Butt both vertical wall studsof side and rear walls
Kommentare zu diesen Handbüchern